# Direct Anterior Hip Arthroplasty

A step\-by\-step surgical module following the Direct Anterior Approach to total hip replacement, from incision to implant

By Russell Smith

Topic: Human Body &amp; Medicine

[Open the interactive Jig](https://ask.jig.com/j/CvdM1uw382tA)

## Transcript

### 1. Direct Anterior Hip Arthroplasty

This model shows a right hip from the front, as the surgeon sees it with the patient lying on their back\. In a total hip arthroplasty \(hip replacement\) the worn ball and socket are replaced with implants\. The direct anterior approach reaches the joint from the front, between muscles rather than through them\. Tap any part to see its name\.

A teaching model of the 16 steps in the guide\. Each surgeon adapts the technique to each patient\.

### 2. 1 · Planning and Positioning

The patient lies supine \(on their back\)\. Feel for the ASIS, the bony point at the front of the pelvis, and the greater trochanter, the bony bump at the top of the thigh bone\. Mark an incision that starts about 3 cm lateral and 1–2 finger breadths distal \(towards the feet\) to the ASIS, running down the thigh for only 8–10 cm\.

This line is well lateral of the classic Smith\-Petersen interval, keeping away from the lateral femoral cutaneous nerve\.

### 3. 2 · The Portal

Open the skin along the mark\. Underneath lies the tensor fasciae latae \(TFL\), a muscle wrapped in fascia, a tough white sheet of tissue\. The interval between the TFL and the sartorius is felt along its length, and access is made strictly lateral, under the TFL fascia\.

Branches of the lateral femoral cutaneous nerve lie medial to the tensor; staying under its fascia protects them\.

### 4. 3 · Lateral Retractors

Incise the TFL fascia slightly medial to its midpoint and pull the tensor gently laterally\. Place a blunt retractor \(1\), a curved steel blade that holds tissue aside, on the superolateral femoral neck and a sharp retractor \(2\) inferolateral to the greater trochanter\. Find the ascending branches of the lateral circumflex vessels, small blood vessels crossing this gap, and cauterise \(seal with heat\) them\.

These vessels vary in number and size and can bleed a lot, so control them before going deeper\.

### 5. 4 · Medial Retractors

Release the deep fascia between the rectus femoris and the capsule\. Place a blunt retractor \(3\) at the soft spot inferomedial to the neck, holding the rectus and sartorius aside\. With the hip flexed, a fourth curved retractor \(4\) goes on the anterior rim of the acetabulum \(the socket\), under the iliopsoas, the big muscle that bends the hip\.

Keep retractor 4 on bone and perpendicular to the ilioinguinal ligament, away from the femoral nerve and vessels\.

### 6. 5 · Preparation of the Capsule

The capsule is the tough sleeve around the joint\. Incise it along the axis of the femoral neck, from the acetabulum to the intertrochanteric line, as an H\-shaped capsulotomy or a capsulectomy\. Move retractors 1 and 3 inside the capsule and clear the saddle region between neck and trochanter\.

### 7. 6 · Removal of the Femoral Head

Make two cuts through the femoral neck with a narrow saw: one close to the head, and one from the saddle towards a point about 1 cm above the lesser trochanter\. Lift out the wedge of neck between them\. Then drill the Femoral Head Extractor into the head and ease the head out with the T\-handle\.

Removing a wedge first makes room, so the head comes out without forcing it\.

### 8. 7 · Preparing the Acetabulum

Keep the retractor on the anterior rim and reposition the others around the socket: inferomedially at the transverse ligament, posterolaterally, and a Mueller retractor on the posterior rim\. Remove the remaining labrum \(the soft rim of the socket\), then ream the socket into a clean half\-sphere with a reamer on an offset handle\.

The offset handle clears the thigh tissue and avoids pressing on the anterior wall\.

### 9. 8 · Cup Insertion

Thread the Cup Impactor Bolt into the shell and fix it to the cup impactor\. Set the cup’s angle and impact it into the reamed socket\. The optional alignment guide approximates 45° of inclination and 20° of anteversion \(forward tilt\)\.

Remove the bolt by turning it counterclockwise\. Turning it clockwise tightens it into the cup\.

### 10. 9 · Screw Placement

If extra fixation is wanted, drill through a hole in the cup with a flexible drill and guide\. Then drive the screw with a flexible or universal\-joint screwdriver until its head sits flush inside the shell\.

Screws are optional; this depends on the bone and the surgeon’s judgement\.

### 11. 10 · Liner Insertion

Insert the liner, the smooth bearing surface the new head will move against, and seat it firmly in the shell with a liner impactor\. The acetabular side of the new joint is now complete\.

### 12. 11 · Posterolateral Capsule

Take out the acetabular retractors and place the leg in adduction \(towards the other leg\) and external rotation \(turned outwards\)\. With retractors at the greater trochanter, free the posterolateral capsule with electrocautery until the short external rotators come into view\.

### 13. 12 · Figure 4 Position

On a standard table, remove the retractors, flex the knee and turn the leg out so the foot rests by the other knee, like the number 4\. This exposes the cut neck, the calcar\. Mark the femur’s neutral rotation on the calcar with electrocautery to guide the stem’s version later\.

Optional, for standard table users only\.

### 14. 13 · Exposure of the Femur

Extend the leg 30–40° with the knee straight, then adduct and externally rotate it\. Place a long Mueller retractor behind the greater trochanter, hook the calcar with the Bone Hook and slowly lift the femur forward and outward\. Release posterior structures only if needed\.

Always combine the pull of the hook with the lever of the retractor to spare the greater trochanter\.

### 15. 14 · Opening the Femoral Canal

Sound the direction of the canal \(the hollow centre of the femur\) with an angled curette\. Remove bone from the superolateral neck with the Modular Box Osteotome, so the broach and stem do not end up undersized or tilted into varus \(angled inwards\)\.

The Reverse Cutting Rasp can also lateralise the opening; it cuts only as it is pulled out\.

### 16. 15 · Broaching the Femur

A broach is a toothed shaping tool the size of the stem\. Push the smallest broach in on the Dual\-Offset Handle, aligned with the planned version, and tap it lightly only once it is fully introduced\. Increase sizes, then trial with heads until length, motion and stability are right\.

### 17. 16 · Implantation and Closure

Insert the final stem by hand and advance it with a bullet\-tip impactor\. Impact the head onto the trunnion \(the stem’s tapered neck\) and check it with traction\. Relocate the head into the cup, recheck the hip, and close in layers\.

A cemented stem follows its own cementing technique before this step\.
