# Open Duck Mini v2 Assembly

Build the Open Duck Mini v2 bipedal robot step by step, including every wire and connection

By PETE\!

Topic: Engineering

[Open the interactive Jig](https://ask.jig.com/j/EeFYP3TBQSKT)

## Transcript

### 1. Open Duck Mini v2

This open\-source bipedal robot is about 43 centimetres tall to the top of its head\. It has 14 bus servos, a Raspberry Pi Zero 2 W in its head and a two\-cell battery in its body\. Follow the steps to print, assemble and wire it\.

Print every part in PLA except the two foot soles, which are TPU\.

### 2. 1 · Set the Servo IDs

Give each STS3215 servo its ID before you fit it\. The right leg uses IDs 10 to 14 from hip yaw to ankle, and the left leg uses 20 to 24\. The neck and head servos are 30 to 33\. Centre every horn at its zero position\.

Label each servo with its ID so it goes into the right joint\.

### 3. 2 · Trunk

Press the two hip bearings and the M3 inserts into the trunk bottom, then join the trunk top with two M3 by 10 screws\. Mount the two hip yaw servos on top, then slide the roll motor bottom brackets in underneath\.

### 4. 3 · Feet

Stack each foot from the TPU sole up: the PLA base, an SS\-10 switch at the heel, the ankle servo, then the top and side plates\. Both feet are identical\.

The switch lever must reach the sole so it clicks when the foot touches the ground\.

### 5. 4 · Shins

Screw the inner shin sheet to the ankle servo horn, add the leg spacer and the knee servo, then close the shin with the outer sheet\. Use the plastic servo screws\.

### 6. 5 · Thighs

Build the thighs the same way: inner sheet on the knee horn, spacer, hip pitch servo, then the outer sheet\.

### 7. 6 · Hips

Fit the roll motor top under each hip yaw servo, then the hip roll servo, and link it to the hip pitch servo with the roll\-to\-pitch part\.

The left and right roll\-to\-pitch parts are mirrored\. Check the side before you screw them in\.

### 8. 7 · Neck

Mount neck pitch servo 30 on the trunk and fit the left and right neck sheets to it\. Add head pitch servo 31 between the sheets\. Slide the body middle top section over the trunk now, while it still fits\.

### 9. 8 · Head Mechanism

Fit the pitch\-to\-yaw bracket, head yaw servo 32, the yaw\-to\-roll bracket with its bearing, head roll servo 33 and the roll mount\. Then fit the head bottom plate\.

### 10. 9 · Battery and Power

Fit the two 18650 cells in series, then the BMS, the USB\-C charger, the power switch, the bus servo board and the IMU\. Wire the cells to B\+, BM and B− on the BMS\. Then run P\+ through the switch to the board’s 7\.4 volt jack, with P− to its ground\. The charger connects across P\+ and P−\.

Check the cell polarity before you connect the BMS\.

### 11. 10 · Servo Bus

Daisy\-chain the servo cables\. One board port runs the right leg from 10 to 14, another the left leg from 20 to 24, and a third the neck and head from 30 to 33\. All servos share one bus, so the order along a chain does not matter\.

### 12. 11 · Head Electronics

On the head plate, fit the UBEC, the Raspberry Pi Zero 2 W with its microSD card, the MAX98357A amplifier and the speaker\. Then add the two SG90 antenna servos and their holders, the projector LED and the camera\.

### 13. 12 · Wire the Pi

Run a USB cable from the Pi to the servo board, the 7\.4 volt feed to the UBEC and the IMU to I²C on pins 1, 3, 5 and 9\. Wire the foot switches to GPIO27 for the right foot and GPIO22 for the left\. Then connect the antenna servos, LEDs, amplifier and speaker, and plug the camera ribbon into the CSI port\.

The UBEC’s 5 volt output feeds the Pi on pins 2 and 6\.

### 14. 13 · Close the Head

Lower the head shell over the electronics, press the eyes into the front holes and push the antennas into the servo holders\.

### 15. 14 · Close the Body

Fit the body bottom, front and back, then close the battery lid\. Clip the covers onto both thighs\.

### 16. 15 · Wiring Map

Here is all the wiring with the shells shown see\-through\. The servo bus is dark grey, the battery power runs in red and black, and the Pi harness runs up the neck to the head\.

### 17. Done

Charge the battery over USB\-C, switch the duck on and check that every servo answers on the bus before its first walk\.
