# Christmas Market Stand Build

Build a sturdy little Christmas market stand from 23 wooden laths, step by step, with glue, screws and a striped roof

By Mahdi El hasra

Topic: Home &amp; DIY

[Open the interactive Jig](https://ask.jig.com/j/Ok4v3U51BQRr)

## Transcript

### 1. Christmas Market Stand

All 23 laths are 120 × 5\.5 × 1\.7 cm\. First saw three of them in half to get six 60 cm pieces\. You also need wood glue, about 40 wood screws \(4 × 40 mm\), a screwdriver or cordless driver, a 3 mm drill bit and a striped cloth for the roof\. Tap any part to see its name\.

A grown\-up does the sawing and drilling\. Children can sand, hold and pass parts\.

### 2. 1 · Glue the First Corner Post

Stand one lath on its narrow edge and spread glue along the top\. Lay a second lath flat on it so the two make an L shape\. An L is much stiffer than a flat lath, so your posts will not bend\.

### 3. 2 · Screw the Post Together

Drill a small pilot hole first, so the wood does not split\. Then drive a 4 × 40 mm screw down through the flat lath into the edge below\. Add one about every 20 cm, six per post\.

Keep screws at least 2 cm from the ends of a lath\.

### 4. 3 · Make the Other Three Posts

Glue and screw the other three pairs the same way\. Now you have four strong corner posts, each 120 cm tall\. They use 8 of your 23 laths\.

### 5. 4 · Stand Up the Left Posts

Stand two posts upright, 60 cm apart, with the open side of each L facing in\. Ask a helper to hold them steady while you work\.

### 6. 5 · Add the Left Rail and Brace

Glue and screw a 60 cm rail across both posts with its top 80 cm above the floor\. Then fix a 60 cm brace slanting below it\. A slanting brace makes triangles, and triangles cannot wobble\.

Two screws at every crossing, one above the other, stop the joint from turning\.

### 7. 6 · Stand Up the Right Posts

Stand the last two posts upright on the right, 120 cm from the left ones\. Keep the open sides of the L shapes facing in\.

### 8. 7 · Add the Right Rail and Brace

Fix the right rail and brace exactly like the left ones\. Measure from the floor so both rails are at the same height\.

### 9. 8 · Tie the Back Together

From behind, screw a full lath across the back posts at counter height\. Then fix one long lath slanting from low on the left to high on the right\. This big triangle stops the stand from leaning sideways\.

Measure both corner\-to\-corner diagonals: when they are equal, the frame is square\.

### 10. 9 · Lay the Counter

Lower five laths onto the two side rails, side by side with a finger\-wide gap\. Glue and screw each end down\. This is the counter where you will sell your cookies and crafts\.

### 11. 10 · Add the Top Rails

Screw the last two 60 cm rails along the tops of the sides\. Then fix a full lath across the back and one across the front\. The front one is your sign board\.

### 12. 11 · Lay the Roof Laths

Lay three laths across the top, at the front, middle and back\. Screw them down into the top rails\. They hold the roof cloth up\.

### 13. 12 · Spread the Roof Cloth

Lay the striped cloth over the roof laths and fasten it with a few staples or drawing pins along the edges\. It gives your stand a real market look\.

### 14. Your Stand Is Ready

Push gently on each corner: a well\-built stand does not wobble\. Add a fir garland, fairy lights and a name on the sign board\. All 23 laths are used, with nothing left over\.

Outdoors, tie the stand down or weigh its feet so the wind cannot tip it\.
