# IKEA \- HEMNES Day\-Bed with 3 Drawers Assemble an IKEA HEMNES day\-bed frame with three drawers step by step, following manual AA\-1917803 By Numa Topic: Home & DIY [Open the interactive Jig](https://ask.jig.com/j/UF2uqc5Pf7JS) ## Guide ### 1. Parts and Tools The HEMNES day\-bed frame, single size, in three parts: the pull\-out bed base on the rug, the bed frame by the wall and the three drawers on the left\. You need a cross\-head screwdriver, a flat screwdriver and a hammer; the hex key comes in the box\. Tap a part to see its name\. Two people are needed to stand the frame up, turn it over and slide the base in\. ### 2. Base 1 · First Castor Lay the four rails upside down\. Set a castor on the first rail near one end, wheel up, its plate flat on the rail\. ### 3. Base 1 · First Castor Screw Drive a 109049 screw through the castor plate into the rail, clockwise with the cross\-head screwdriver\. ### 4. Base 1 · Other Seven Castors Set the other seven castors in place: one near each end of every rail\. ### 5. Base 1 · Other Seven Screws Screw each castor down the same way, one screw per plate\. ### 6. Base 2 · Rails on Their Castors Turn the four rails over so they stand on their castors\. ### 7. Base 2 · First Right Runner Hold a runner marked CR against the side of the second rail, its roller end at the end with three holes\. ### 8. Base 2 · First Runner Screw Drive a 100347 screw through the runner into the rail, clockwise\. Use the short 100347 screws here, not the 116894\. ### 9. Base 2 · Its Other Two Screws Fix the runner with two more screws\. ### 10. Base 2 · Two More Right Runners Hold the other two CR runners against the third and fourth rails, on the same side\. ### 11. Base 2 · Their Six Screws Screw them on with three screws each\. ### 12. Base 3 · Three Left Runners Hold the three CL runners against the other side of the first three rails, roller end at the same end\. ### 13. Base 3 · Their Nine Screws Screw them on with three 100347 screws each\. ### 14. Base 4 · First Wood Dowel Push a wood dowel into a hole in the end of a rail until half of it is in\. ### 15. Base 4 · Other Fifteen Push in the other fifteen: two in each end of every rail\. ### 16. Base 5 · Profile on the Back Board Lay the plain back board flat on the rug, inner face up\. Set the long metal profile along its lower edge, flange on the board\. ### 17. Base 5 · First Profile Screw Drive a 116894 screw through the hole at one end of the profile, clockwise\. These have the wider head; do not use the 100347 screws here\. ### 18. Base 5 · Second Screw Drive a second screw at the other end of the profile\. ### 19. Base 6 · Six More Screws Drive six more 116894 screws through the slots along the profile\. ### 20. Base 7 · First Cam Dowel Screw a cam dowel into a hole in the board's inner face, clockwise, until its collar meets the board\. ### 21. Base 7 · Other Seven Screw in the other seven: two for each of the four rails and the end panels, along the board's ends and between its windows\. ### 22. Base 8 · Rails onto the Board Stand the four rails on the board, dowels into its holes and cam dowels into the rails' side holes, and push them home\. ### 23. Base 9 · First Cam Lock Drop a cam lock into the round hole in a rail's side, arrow towards the board\. Turn it clockwise with the flat screwdriver until it grips the cam dowel\. ### 24. Base 9 · Other Three Fit and tighten a cam lock in each of the other three rails\. ### 25. Base 10 · Dowels in the End Panels Push wood dowels into the edge holes of both end panels, half of each one in\. ### 26. Base 11 · End Panels On Stand the two end panels at the ends of the board and push them onto its dowels\. ### 27. Base 12 · Their Cam Locks Fit four cam locks in the end panels, two in each, and tighten them clockwise\. ### 28. Base 13 · Profile on the Front Board Lay the front board with its three drawer openings face down\. Set the second profile along its lower edge\. ### 29. Base 13 · Two Screws Fix the profile with a 116894 screw at each end\. ### 30. Base 14 · Six More Screws Drive six more 116894 screws through the slots along the profile\. ### 31. Base 15 · Eight Cam Dowels Screw eight cam dowels into the front board's inner face, clockwise, as on the back board\. ### 32. Base 16 · Front Board On Lift the front board over the rails and end panels and push it down onto their dowels\. ### 33. Base 17 · Four Cam Locks Fit a cam lock in each rail at the front board and tighten it clockwise\. ### 34. Base 18 · Four More Cam Locks Fit and tighten the four cam locks in the end panels at the front board\. ### 35. Base 19 · Three Fixed Slats Lay three of the short slats on the profiles above the middle rails, through the openings' dividers\. Use the shorter slats here, not the longer ones\. ### 36. Base 19 · Their Six Screws Screw each slat to both profiles with a 116894 screw at each end\. ### 37. Base 20 · First Slat Peg Lay the other eighteen slats in a row, underside up\. Push a peg into the hole at one end of the first slat until its collar meets the wood\. ### 38. Base 20 · Other Seventeen Push a peg into each of the other seventeen slats\. ### 39. Base 21 · Stand the Base Up Tip the base back onto its castors and turn it round, front board towards you\. ### 40. Base 21 · Eighteen Slats Lay the eighteen slats across the base, each peg down into its hole in the profile\. The bed base is done\. ### 41. Frame 1 · Profile on the Back Panel Lay the long back panel flat by the wall, inner face up\. Set the third profile along its lower rail\. ### 42. Frame 1 · Two Screws Fix the profile with a 116894 screw at each end, clockwise\. ### 43. Frame 2 · Six More Screws Drive six more 116894 screws through the slots along the profile\. ### 44. Frame 3 · Dowels in the End Panels Push three wood dowels into the edge of each end panel, half of each one in\. ### 45. Frame 4 · Stand the Back Panel Up Stand the back panel up on its feet against the wall\. Two people: hold the panel until both end panels are bolted on\. ### 46. Frame 4 · End Panels On Push the end panels onto the dowels at the ends of the back panel\. ### 47. Frame 4 · First Barrel Nut Push a barrel nut into the round hole in the side of an end panel, slot facing out\. ### 48. Frame 4 · Other Three Nuts Push in the other three nuts: two in each end panel\. ### 49. Frame 4 · First Bolt Put a 105236 bolt through the back panel's post into the nut and tighten it clockwise with the hex key\. ### 50. Frame 4 · Other Three Bolts Tighten the other three bolts the same way\. ### 51. Frame 5 · Turn the Frame Over Turn the frame upside down, onto the tops of its posts\. ### 52. Frame 5 · First Foot Insert Push a foot insert into the hole in the end of a post\. ### 53. Frame 5 · Other Three Push a foot insert into each of the other three posts\. ### 54. Frame 6 · The Brace Set the long brace between the two front posts, along the open front of the frame\. ### 55. Frame 6 · Two Caps Fit a cap between each end of the brace and the post\. ### 56. Frame 6 · First Brace Screw Drive a long 109060 screw through the brace and cap into the post, clockwise\. Use the long 109060 screws here, not the 116894\. ### 57. Frame 6 · Other Three Drive the other three screws: two at each end\. ### 58. Frame 7 · Right Way Up Turn the frame back onto its feet\. ### 59. Frame 7 · Brackets on Two Slats Take the two slats with small holes in one side\. Set a bracket under the end of each\. ### 60. Frame 7 · Their Four Screws Fix each bracket with two 116894 screws\. ### 61. Frame 8 · Bracket Slats In Lay the two bracket slats across the frame, one at each end\. ### 62. Frame 8 · Screws from Below From underneath, drive two 116894 screws up into each of them\. ### 63. Frame 9 · Pegs in Eleven Slats Push a peg into the hole at one end of each of the other eleven slats\. ### 64. Frame 10 · Eleven Slats In Lay the eleven slats across the frame, peg end into the hole in the profile\. Do not sit or stand on the frame until it is finished\. ### 65. Frame 10 · Their Screws Screw the other end of each slat down with a 116894 screw\. ### 66. Frame 11 · Slide the Base In Roll the pull\-out base in under the bed frame from the front until it stops\. One person lifts the end panel a little so the base can pass\. ### 67. Frame 12 · First Plastic Pin Set a plastic pin in a hole in the top edge of the back panel and tap it in with the hammer\. ### 68. Frame 12 · Other Sixteen Tap in the other sixteen pins along the tops of the back and end panels\. ### 69. Frame 13 · Back Top Rail Push the long top rail down onto the pins along the back panel\. ### 70. Frame 14 · End Top Rails Push the two short top rails onto the end panels\. ### 71. Drawer 1 · Eight Cam Dowels Lay the drawer front face down and the back board beside it\. Screw four cam dowels into each, clockwise\. ### 72. Drawer 2 · Sides On Push the two sides onto the drawer front's cam dowels\. ### 73. Drawer 3 · First Cam Lock Drop a small cam lock into a hole in a side and turn it clockwise with the flat screwdriver until it grips\. ### 74. Drawer 3 · Other Three Fit and tighten the other three: two in each side\. ### 75. Drawer 4 · Bottom In Slide the bottom panel into the grooves in the sides and the front\. ### 76. Drawer 5 · Back Board On Push the back board onto the ends of the sides\. ### 77. Drawer 6 · Four Cam Locks Fit and tighten four more cam locks at the back board\. ### 78. Drawer 7 · Runners On Hold runner DL against the left side and DR against the right\. ### 79. Drawer 7 · Six Screws Screw each runner on with three 100347 screws\. ### 80. Drawer 8 · Stand It Up Stand the drawer up on its bottom, front towards you\. ### 81. Drawer 8 · Knob Set the knob on the front of the drawer over its hole\. ### 82. Drawer 8 · Knob Screw From inside the drawer, drive the 119976 screw through the front into the knob, clockwise\. ### 83. Drawers · Two More Build the other two drawers the same way\. ### 84. Drawer 9 · Slide the Drawers In Set each drawer's runners on the runners in the base and push it in\. The day\-bed is ready\.