ExploreMy JigsMission
MakeMake a Jig

© JigSpace Inc. 2026

jig.comContact@JigSpace on X

Build a 5-inch FPV Drone

publicRemix · Free
PBy PETE!

Assemble the Master 5 V2 frame and solder the F405 V5 stack, motors, O4 Pro, receiver and GPS

Transcript

17 steps · 4 min read
  1. 1

    Step 1: Build a 5-inch FPV Quad

    A SpeedyBee Master 5 V2 frame with the F405 V5 / 55A stack, XING-E Pro 2207 motors, DJI O4 Air Unit Pro, RP3-H receiver and WS-M181 GPS. Follow the frame, wiring and soldering in order.

    Props stay off until the very end. Never solder with a battery plugged in.

  2. 2

    Step 2: 1 · Arms and Middle Plate

    Lay the four 5 mm arms on the bottom plate, set the middle plate on top and drive the M3 × 11 arm screws through all three layers.

    Snug, not stripped: thread locker on screws that go into metal.

  • 3

    Step 3: 2 · Camera Plates, GPS Base, Standoffs

    Fit the TPU camera side plates at the front and the 18 mm GPS base at the rear, then screw the four M3 × 23 aluminium standoffs into the middle plate.

  • 4

    Step 4: 3 · O4 Air Unit Pro

    Mount the camera between the side plates at about 15° up-tilt and the air unit at the rear. Lay the camera cable flat along the middle of the plate and lead both antennas out of the back.

    Never power the O4 without its antennas fitted.

  • 5

    Step 5: 4 · Stack Mount and ESC

    Press the TPU stack module onto the 30.5 mm holes and seat the SpeedyBee 55A 4-in-1 ESC on it with its battery pads to the rear.

    SpeedyBee suggests the ESC turned 180°; remap the motors in Betaflight afterwards.

  • 6

    Step 6: 5 · Motors

    Screw each XING-E Pro 2207 to its arm tip from below with short M3 screws, then lay the three leads flat along the arm towards the ESC.

    A screw that touches the windings will short the motor: check the length.

  • 7

    Step 7: 6 · Trim the Motor Leads

    Cut each lead just long enough to reach its pad without tension, then strip about 2 mm of insulation from every wire.

    The manual gives about 110 mm for the inner and 93 mm for the outer wires.

  • 8

    Step 8: 7 · Solder the Motor Wires

    Tin each pad and wire first. Then hold the wire on its pad and touch the iron for two to three seconds until the solder flows into a shiny fillet. Order does not matter: direction is set in software.

    Iron about 350 °C; a dull, balled joint needs reheating.

  • 9

    Step 9: 8 · XT60 Lead and Capacitor

    Solder the 1000 µF 35 V capacitor across the battery pads with short legs, then the XT60 lead: red to B+, black to B−. Keep both clear of where the flight controller will sit.

    Mind the stripe: it marks the capacitor’s negative leg.

  • 10

    Step 10: 9 · Flight Controller

    Put the silicone grommets in the stack holes and seat the F405 V5 on them, arrow forward. Plug in the 10-pin ESC cable underneath first.

  • 11

    Step 11: 10 · Prepare the GPS Lead

    The WS-M181 comes with a JST plug. To solder it to the pads instead, cut the plug off, strip about 2 mm from each of the six wires, twist the strands and tin them.

    Check which colour is TX, RX, SDA and SCL on the GPS label first.

  • 12

    Step 12: 11 · GPS to the UART4 Pads

    Stick the GPS on its base, arrow forward, and run the wires to the UART4 pads: 5V to 4V5, GND to G, GPS TX to R4, GPS RX to T4, SDA to SDA and SCL to SCL.

    TX and RX always cross. Betaflight: UART4 Sensor Input = GPS.

  • 13

    Step 13: 12 · Receiver to UART6

    Fix the RP3-H on top of the air unit and lead its two antennas out of the back. Solder 5V to 4V5, GND to G, receiver TX to R6 and receiver RX to T6.

    Betaflight: Serial RX on UART6, receiver CRSF.

  • 14

    Step 14: 13 · O4 to UART3

    Solder the O4 3-in-1 cable to the UART3 block: red to 9V, black to G, grey (O4 TX) to R3 and white (O4 RX) to T3. Leave the unused wires insulated.

    The O4 runs on 9 V or battery voltage, never on 5 V.

  • 15

    Step 15: 14 · Buzzer

    Stick the 5 V active buzzer under the front of the stack and solder red to BZ+ and black to BZ−. It beeps on lost signal and helps you find the quad in grass.

  • 16

    Step 16: 15 · Top Plate

    Check every joint for bridges and loose strands, tie the wires down, then screw the top plate onto the standoffs.

  • 17

    Step 17: Done: Battery and Setup

    Strap the 6S 1300 mAh pack on the silicone pad. In Betaflight set UART4 to GPS, UART6 to CRSF, UART3 to VTX (MSP), then check motor order and direction before fitting props.

    First power-up through a smoke stopper, props off.