# IKEA \- FRIHETEN Corner Sofa\-Bed Assemble an IKEA FRIHETEN corner sofa\-bed with storage and its chaise longue step by step, following manual AA\-702253 Model credits \(Sketchfab\): “Phillips Head Screw Driver” by brandonh111121, via Sketchfab \(https://sketchfab\.com/3d\-models/78c516b16ecc4b12bb2e6d90d031596e\)\. CC\-BY\-4\.0: https://creativecommons\.org/licenses/by/4\.0/ Prepared for Jig; static geometry/material conversion\. By Numa Topic: Home & DIY [Open the interactive Jig](https://ask.jig.com/j/XXqSeqYksXnN) ## Guide ### 1. Parts and Tools The chaise longue box, the back panels, the seat frame, the armrest, the pull\-out module, the cushions, and every pin, screw, leg, hook and castor, laid out on a rug\. You need a cross\-head screwdriver \(PZ2\); the three hex keys and the key handle are in the box\. Tap a part to see its name\. The manual shows two people for the heavy steps and no power screwdriver\. Build on a soft surface\. ### 2. 1 · Lift the Lid Lift the chaise lid on its right edge until it stands open, so you can reach inside the box\. ### 3. 1 · Fit the Cover Hold the fabric cover with its notched corner at the bottom and set it against the front of the box\. ### 4. 2 · Tuck In the Cover Push the cover's stitched edge into the strip with your thumb, at four places along the front\. ### 5. 3 · Lower the Lid Lower the lid until it rests on the box\. ### 6. 4 · Dowels in the Long Panel Push two dowels into the end of the long back panel until half of each is in\. ### 7. 4 · Join the Short Panel Slide the short back panel onto the two dowels so the panels meet at the corner\. ### 8. 5 · Slide In the Chaise Slide the covered chaise back into the corner, against both back panels\. ### 9. 6 · Click the Key into the Handle Push the 5 mm hex key into the end of the handle until it clicks\. ### 10. 6 · First Pin and Sleeve Screw a threaded pin into a nut sleeve by hand, clockwise\. ### 11. 6 · Other Three Pins Screw the other three pins into their sleeves the same way\. ### 12. 7 · Lift the Lid Again Lift the lid again and keep it open\. Never stand on the lid or its edge\. The lid is not made to carry a person's weight\. ### 13. 7 · First Pin Through the Wall Push a pin and sleeve through the back wall of the box into the panel behind it, then tighten it with the 5 mm key in its handle\. ### 14. 7 · Other Three Pins Fit and tighten the other three pins: one more through the back wall and two through the left wall into the short panel\. ### 15. 8 · Brackets on the Chaise Hold a bracket against the right wall of the box, slots toward the seat, at each of the two marked places\. ### 16. 8 · First Short Screw Fix a bracket with a short screw \(105102\) and the 4 mm hex key\. Check the number: the long screw is for step 14\. ### 17. 8 · Other Three Short Screws Fix the other three short screws the same way\. ### 18. 8 · Lower the Lid Lower the lid\. ### 19. 9 · Turn It onto Its Back Lay the whole assembly down on its back panels, front up\. Two people turn it\. ### 20. 10 · Slide In the Seat Frame Two people slide the seat frame up to the chaise\. Line up the lugs on its lower edge with the holes in the back panel\. ### 21. 11 · First Pin and Sleeve Screw a threaded pin into a nut sleeve by hand\. ### 22. 11 · Other Three Pins Screw the other three pins into their sleeves\. ### 23. 12 · Dowels in the Seat Frame Push two dowels into the right end of the seat frame\. ### 24. 12 · Fit the Armrest Slide the armrest onto the two dowels\. ### 25. 13 · First Pin Through the Frame Push a pin and sleeve through the seat frame into the panel behind it and tighten it with the 5 mm key in its handle\. ### 26. 13 · Other Three Pins Fit the other three: one more into the back panel and two through the right end into the armrest\. ### 27. 14 · First Long Screw Put a long screw \(105109\) through a slot of a bracket into the seat frame and tighten it with the 4 mm key\. ### 28. 14 · Other Three Long Screws Fit the other three long screws the same way\. Do not use the short screws here\. ### 29. 15 · First Leg Screw a leg into the underside, clockwise, until it is tight\. ### 30. 15 · Other Six Legs Screw in the other six legs: four more under the chaise, two under the armrest\. ### 31. 16 · Hooks Hold a hook against the inside of each end of the seat frame\. ### 32. 16 · First Hook Screw Fix a hook with a woodscrew \(118878\) and the 3 mm hex key\. The cross\-head screws are for the castors\. ### 33. 16 · Other Three Hook Screws Fix the other three woodscrews the same way\. ### 34. 16 · Stand It Up Turn the assembly upright again\. Two people turn it\. ### 35. 17 · Castors Hold a castor at each corner of the pull\-out module's underside\. It lies upside down\. ### 36. 17 · First Castor Screw Fix a castor with a cross\-head screw \(109566\) and the screwdriver\. ### 37. 17 · Other Seven Castor Screws Fix the other seven screws\. ### 38. 18 · Stop Pins Hold a stop pin flat against the back edge of the module at each marked place\. ### 39. 18 · First Stop Pin Screw Fix a stop pin with a cross\-head screw\. ### 40. 18 · Other Three Stop Pin Screws Fix the other three screws, pins lying flat and seated\. A pin that sits angled or off the frame will not hold\. ### 41. 18 · Turn the Module Over Turn the module over so the castors face down\. ### 42. 19 · Set In the Module Lower the module into the seat frame with its stop pins against the back\. Two people lift it\. ### 43. 20 · Back Cushions Set the three back cushions on the seat, leaning on the back panels\. ### 44. Finished Your FRIHETEN corner sofa\-bed\. Pull the front forward by its straps to open the bed\.