# Rena Wardrobe Assembly Guide Build the two\-door Rena sliding wardrobe step by step, from loose boards to a wall\-fixed wardrobe By Ferhat Turan Topic: Home & DIY [Open the interactive Jig](https://ask.jig.com/j/cfbLKBXL9yCK) ## Transcript ### 1. Rena Wardrobe Assembly Guide These boards become a sliding\-door wardrobe 120 cm wide and 235 cm tall, taller than most grown\-ups\. Each board has a number, like 01 or 07, that matches the paper manual\. Tap any part to see its name\. Allow about 105 minutes\. Work with two people, and four when you stand it up\. ### 2. S6 · Stand the Plinth Strips The two plinth strips \(09\) are the low rails the wardrobe stands on\. Set them on their long edges, one at the front and one at the back\. Lay big boards on a blanket so they do not get scratched\. ### 3. S6–S7 · Fit the Bottom Board Lower the bottom board \(07\) onto the strips\. Its top carries the double track the doors will roll in\. Cam locks, small round catches turned with the Allen key, pull each joint tight\. ### 4. S2, S7 · Stand the Divider Stand the divider \(04\) in the middle of the bottom board\. It splits the wardrobe into two compartments, each about 57 cm wide\. ### 5. S1–S3 · Fix the Two Fixed Shelves Push one fixed shelf \(10\) onto each side of the divider, high up\. Wooden dowels line the boards up, and the cams lock them\. Turn each cam clockwise until its arrow points at the bolt\. Do not force it\. ### 6. S4–S5 · Lay On the Top Board Lower the top board \(08\) onto the divider\. Its underside has the upper door track, a mirror of the one below\. ### 7. S8, S11 · Slide In the Back Panels The two thin back panels \(03\) slide in from the open sides, one behind each compartment\. A back panel keeps the frame square, so the doors will run straight\. ### 8. S9–S10 · Push On the Right Side Push the right side \(01\) onto the ends of the boards and tighten its cams\. The rows of little holes inside are for the shelf pins later\. The manual builds the frame lying on the floor, then four people stand it up\. It is shown standing here so every joint is easy to see\. ### 9. S12–S23 · Ready the Doors Lay both doors \(05, 06\) face up\. Slide a black handle profile \(M08\) along each outer edge and screw it on\. This slim aluminium edge is the handle you pull\. The manual also fits four rollers and a soft\-close damper to each door here\. ### 10. S24–S25 · Hang the Sliding Doors Lift door 06 into the back track first, then door 05 into the front track\. The rollers must sit in the grooves, top and bottom\. ### 11. S26–S27 · Push On the Left Side Push the left side \(02\) onto the board ends and lock its cams\. Press a round cap over each cam to hide it\. ### 12. S33 · Drop In the Hanging Rail Slide the front door aside\. Rest the hanging rail \(F16\) in the two little cups called flanges, under the left shelf\. ### 13. S34 · Fix It to the Wall Screw two angle brackets \(A87\) to the top board and into the wall behind\. A tall wardrobe fixed to the wall cannot tip over, even if someone pulls a door hard\. Wall plugs and screws depend on your wall, so pick ones that suit it\. ### 14. S35 · Add the Adjustable Shelves Slide the right door aside\. Press four shelf pins into the holes for each shelf, then rest the three adjustable shelves \(11\) on them at any height you like\. ### 15. All Done Close the doors and give each one a gentle push\. If a door leans, turn the screw on its bottom rollers to raise or lower that corner\.