ExploreMy JigsMission
MakeMake a Jig

© JigSpace Inc. 2026

jig.comContact@JigSpace on X

Inside a Wind Turbine

publicRemix · Free
NBy Numa

How a 3-4 MW onshore wind turbine turns wind into electricity: lift, yaw, gearbox, generator, pitch, the Betz limit and the grid

Transcript

10 steps · 3 min read
  1. 1

    Step 1: A Giant on the Hill

    This wind turbine's tower is as tall as a 30-storey building, and each of its three blades is 63 m long. Together they sweep a circle 130 m across. Watch the wind stream past it.

    Each blade is about as long as a jumbo jet's wings are wide.

  2. 2

    Step 2: Blades Are Wings

    Slice through a blade and look down on it: it has the shape of an aircraft wing. Air rushing over the curved side speeds up and its pressure drops, so the blade is pulled sideways. This lift, not a push, turns the rotor.

The blade twists along its length, so every part meets the air at the best angle.
  • 3

    Step 3: Slow Rotor, Fast Tips

    The rotor turns only about 12 times a minute, slow enough to count. But each tip travels a 400 m circle on every turn, so it races along at about 80 m/s, nearly 300 km/h. The spirals show the swirls of air the tips leave behind.

    Tip speed = circle × turns per second: 408 m × 12 ÷ 60 ≈ 82 m/s.

  • 4

    Step 4: Facing the Wind

    A wind vane and an anemometer on the roof measure the wind's direction and speed. When the wind swings round, yaw motors turn the whole nacelle on a toothed ring until the rotor faces the wind again.

    Eight small 2.2 kW motors do it: turning slowly through the big ring gear, they have plenty of force. Shown faster than real.

  • 5

    Step 5: Inside the Nacelle

    Lift off the cover and the machinery appears. The rotor turns the thick main shaft, the gearbox speeds it up and a fast shaft spins the generator. A disc brake can hold it all still, and a cooler carries away the heat.

    The nacelle is about the size of a bus: 12 m long and 4 m wide.

  • 6

    Step 6: The Gearbox

    The rotor is far too slow for a generator. Two planetary stages and one parallel stage of gears multiply the speed about 100 times: 12 turns a minute go in, about 1,200 come out.

    Shown 25 times slower. In each planetary stage, three planet gears share the load around a central sun gear.

  • 7

    Step 7: Making Electricity

    Inside the generator, a spinning magnetic field sweeps past coils of copper wire. That pushes an electric current through the coils: up to 3.4 million watts when the wind is strong.

    Shown 25 times slower. A bicycle dynamo works the same way, just much smaller.

  • 8

    Step 8: Too Much Wind

    Slide the wind speed. Below 3 m/s the rotor only idles. From about 12 m/s the turbine makes full power, and in stronger winds the blades twist to spill the extra. Above 25 m/s they turn edge-on and the rotor stops to ride out the storm.

    Twice the wind speed carries eight times the energy: power grows with the cube of the speed.

  • 9

    Step 9: The Betz Limit

    A turbine takes energy by slowing the wind down. Stop the air completely and nothing could flow through; slow it only a little and little energy is taken. The best is to slow it to a third of its speed, which catches at most 59% of the wind's energy.

    Real turbines capture about 35–45%, after losses in the blades, gears and generator.

  • 10

    Step 10: Power to the Grid

    Cables inside the tower carry the electricity down to a transformer, which raises its voltage for the journey. Power lines then carry it to homes across the countryside, whenever the wind blows, day or night.

    A higher voltage means a smaller current, so less energy is lost as heat in the lines.