# Photocopy Machine Anatomy

How a photocopier builds a copy from static charge, using a cutaway office machine to follow toner from the drum to the fused page\.

By Numa

Topic: Machines

[Open the interactive Jig](https://ask.jig.com/j/iz3F1uuzs0eb)

## Transcript

### 1. A copy made of static

A photocopier copies a page by xerography: it builds a picture out of electric charge, then dusts it with a dry powder called toner\. The front of this office copier is cut away so you can see inside\. Press Make a copy and follow the sheet from the glass to the tray\.

Chester Carlson made the first xerographic image in 1938\. The first automatic plain\-paper copier, the Xerox 914, went on sale in 1960\.

### 2. Charge the drum

The turning cylinder is the photoconductor drum\. A photoconductor is a material that insulates in the dark but conducts when light falls on it\. A corona wire at about 15,000 volts ionises the air beside it and sprays the drum with an even charge of about −600 volts, shown by the red marks\. Predict what happens if you switch the corona off\.

Polarity depends on the machine: selenium drums are charged positive, many organic drums negative\. This model shows negative charge\.

### 3. Expose: light removes charge

A lamp sweeps under the glass, and light reflected from the original travels through mirrors and a lens onto the drum\. Where the page is white, light reaches the drum, it conducts, and the charge drains to ground\. Dark text reflects little light, so its charge stays: an invisible latent image made of charge\.

Mirrors 2 and 3 travel at half the lamp's speed\. That keeps the light path the same length, so the image stays in focus\.

### 4. Develop: toner finds the charge

Toner is a powder of plastic and pigment\. Rubbing against carrier beads gives it a positive charge, the triboelectric effect\. Coulomb's law, F = k·q₁·q₂ / r², says opposite charges attract, so toner clings only to the charged image\. Choose the toner's charge and predict whether the image appears\.

With the same sign, the force pushes the toner away and the drum stays clean\. The developer roller's bias voltage keeps toner off the blank areas\.

### 5. Transfer: the jump to paper

Registration rollers hold the sheet, then release it so it meets the image exactly\. Under the paper, a transfer corona charges the back of the sheet more strongly than the drum, so the toner jumps across onto the paper\. The powder is now on the page, but nothing holds it there except static\.

The drum surface, the paper and the scan lamp all move at the same speed, v = ω·r\. Here ω = 1 rad/s and r = 0\.06 m, so v = 0\.06 m/s, slowed down so you can watch\.

### 6. Fuse: heat and pressure

Loose toner would smudge at a touch\. The fuser squeezes the sheet between a heated roller and a rubber pressure roller, melting the toner's plastic into the paper fibres\. Predict what reaches the tray if you switch the heater off\.

Fusing is the only step that uses heat instead of charge, and it is why fresh copies feel warm\.

### 7. Clean and erase

A little toner always stays on the drum after transfer\. A rubber cleaning blade scrapes it off into the waste toner bin\. Then the erase lamp floods the drum with light, so the leftover charge drains away and the surface is blank for the next turn\.

Toner is never wet like ink\. It stays a dry powder until the fuser melts it\.

### 8. Six stations, one turn

Every copy is one trip around the drum: charge, expose, develop, transfer, clean and erase, with the fuser finishing the page\. A laser printer uses the same drum process; only exposure changes, with a laser drawing the image\. Make another copy and name each station as it works\.

Most modern copiers scan the page with a sensor and expose the drum with a laser or LEDs\. This model shows the classic lamp\-and\-mirror light path\.
