# Nasinge Masa Assembly Steps Build the NÄSINGE extendable dining table, step by step, from the manual By Mustafa G Topic: Home & DIY [Open the interactive Jig](https://ask.jig.com/j/pSqZ9oDbAZSW) ## Guide ### 1. NÄSINGE: What Is in the Box This dining table grows from 130 to 190 cm long when you slide its top out and drop in a 60 cm leaf\. Here are the boards, legs, leaf and three bags of small parts\. Tap any part to see its name and number\. Build it with two people, on a rug or the flattened carton so nothing gets scratched\. You need a cross\-head and a flat screwdriver and a hammer\. ### 2. 1 · Brackets on the Long Rails Fix a steel corner bracket \(122483\) at each end of both long rails, with two 100325 screws each\. Turn the screwdriver clockwise to tighten\. ### 3. 2 · Fit the Stop Blocks Screw one plastic stop block \(10103580\) onto each long rail near its left end, using one small 108445 screw\. ### 4. 3 · Four Dowel Bolts Screw the four dowel bolts \(118331\) into the long rails, two on each\. Their grey ribbed part stays sticking out\. ### 5. 4 · Two Round\-Head Bolts Screw one smooth round\-head bolt \(156685\) into the hole in the middle of each long rail\. ### 6. 5 · Dowels in the Beams Push two wooden dowels \(101350\) into both ends of each thin beam: eight in all\. A dowel is a small wooden peg that lines boards up\. Lay the cross rails with their round holes facing up\. ### 7. 6 · Make the H Frame Push the beams into the cross rails to make an H shape\. Then press one more dowel into each end of the cross rails\. ### 8. 7 · Swing the Long Rails Up Lift each long rail up onto the ends of the H frame, so its bolts and dowels slide into the holes\. Press it home near the bracket\. ### 9. 8 · Lock with Four Cams Drop a cam lock \(103430\) into each round hole in the cross rails\. Turn it clockwise with the flat screwdriver: it grips the bolt and pulls the joint tight\. ### 10. 9 · The Latch Fix the steel latch \(10062668\) to one end board with two 100325 screws\. Use only this short screw here, not 109021 or 10082399\. ### 11. 10 · Close the Frame Hold the end boards against the brackets and fix each bracket with two 100325 screws\. Then turn the whole frame over\. ### 12. 11 · Press In the Slide Rails Press a slide rail \(10120478\) down into the groove along the top edge of each long rail, until it sits flush at both ends\. ### 13. 12 · Fit the Four Clips Hook a toothed clip \(10035950\) into each notch in the long rails and fix it with one 109535 screw\. Then turn the frame over again\. ### 14. 13 · Frame onto the Top Lay the tabletop face down\. Lower the frame onto it so its rails sit in the guides on the underside\. ### 15. 14 · Hook Both Ends Slide the frame along the rails until both ends are hooked on\. It should glide without forcing\. ### 16. 15 · Two Stop Bolts Screw two round\-head bolts \(156685\) into the holes in the underside of the top\. They stop the top from sliding too far\. ### 17. 16 · Block and Pin From bag 2, fit the plastic block \(10082205\) with its steel pin \(10064763\) using two long 10082399 screws\. Only this screw fits here\. ### 18. 17 · Two Flat Plates Screw two flat plates \(10103587\) to the top near its end, each with two 100325 screws\. They will hold the leaf later\. ### 19. 18 · Slide the Frame Into Place Slide the frame along the rails until it is nearly at the end of the top\. ### 20. 19 · Click\! Give one last push\. The latch snaps over the block’s pin with a click: the table is now locked closed\. ### 21. 20 · Prepare the Four Legs Push a cross dowel \(110912\) into the hole in the top of each leg by hand; a flat screwdriver turns its slot to line up its holes\. Then screw in two studs \(100033\) clockwise\. ### 22. 21 · Fit the Legs Set each leg in a corner so its studs pass through the bracket\. Add a spring washer \(100843\) and a nut \(100712\) to each stud and tighten with the tube spanner \(120202\)\. ### 23. 22 · Glides, Then Stand It Up Tap a glide \(107271\) into each foot with the hammer; glides protect your floor\. Then, with two people, turn the table onto its legs\. Next comes the leaf: the top will slide out to make room for it\. ### 24. 23 · Plates on the Leaf Lay the leaf face down\. Screw two flat plates \(10103587\) along one edge, each with two 100325 screws\. ### 25. 24 · Triangle Brackets From bag 3, fit two triangular brackets \(10035981\) at the other edge, each with two 109021 screws\. ### 26. 25 · Block and Pin on the Leaf From bag 2, fit the second block \(10082205\) and pin \(10064763\) with two 10082399 screws, just like step 16\. ### 27. 26 · Unlock and Pull Out Unlock the latch by swinging its lever hook down\. Then pull the top out to open a gap at the end\. ### 28. 27 · The Cover Strip Lay the thin strip \(112608\) along the end of the frame, where the leaf will rest\. ### 29. 28 · Lower the Leaf Hold the leaf face up and tilt it into the gap, letting its triangle brackets hook under the plates first\. Then lower it flat\. ### 30. 29 · Push Together and Lock Push the top back against the leaf until the latch clicks: locked\. Your NÄSINGE now seats six\. To shorten it, unlock, pull out, lift the leaf away and push the top home\.