ExploreMy JigsMission
MakeMake a Jig

© JigSpace Inc. 2026

jig.comContact@JigSpace on X

IKEA - KURA Reversible Bed, White/Pine

publicRemix · Free
NBy Numa

Assemble the IKEA KURA reversible bed (90x200 cm) in its loft position step by step, following manual AA-1577020

Transcript

47 steps · 5 min read
  1. 1

    Step 1: Parts and Tools

    The IKEA KURA reversible bed, 90 x 200 cm, built as the loft bed drawn on the manual's cover. The two end panels lie either side of the bed's place, the two side assemblies on the rug, and the ladder post, rungs, rails, slat channels and slats beyond it. You need a flat screwdriver; the hex keys come in the box. Tap a part to see its name.

    Two people are needed to stand the panels up and to roll the frame over.

  2. 2

    Step 2: Panel 1 · Three Rails

    Lay bar 1 along the back of the four-board end panel. Push three of the five rails against its inner face, at the two ends and the middle.

  • 3

    Step 3: Panel 1 · First Screw

    Drive a 128745 screw through bar 1 into the end of a rail, clockwise, with the hex key.

  • 4

    Step 4: Panel 1 · Other Two Screws

    Drive the same screw into the other two rails.

  • 5

    Step 5: Panel 1 · Two More Rails

    Push the other two rails against bar 1, between the first three.

  • 6

    Step 6: Panel 1 · Four Boards

    Slide the four boards between the five rails, towards bar 1.

    The boards are loose in their slots. Do not glue them.

  • 7

    Step 7: Panel 1 · Bar 2

    Set bar 2 against the other ends of the rails, parallel to bar 1.

  • 8

    Step 8: Panel 1 · Three Screws

    Drive a 128745 screw through bar 2 into each of the three rails that carry screws on bar 1.

  • 9

    Step 9: Panel 2 · Three Rails

    Lay bar 3 and push the three rails of the guard-end panel against its inner face.

  • 10

    Step 10: Panel 2 · Three Screws

    Drive a 128745 screw through bar 3 into each rail.

  • 11

    Step 11: Panel 2 · Board

    Slide the single board between the middle and upper rails, towards bar 3.

  • 12

    Step 12: Panel 2 · Bar 4

    Set bar 4 against the other ends of the rails.

  • 13

    Step 13: Panel 2 · Three Screws

    Drive a 128745 screw through bar 4 into each rail.

  • 14

    Step 14: Side 1 · First Nut

    The two rails of each side assembly lie either side of a short crossbar. Push a cross-dowel nut into the crossbar, slot facing up.

  • 15

    Step 15: Side 1 · Other Three Nuts

    Push in the other three nuts: two in each crossbar.

  • 16

    Step 16: Side 1 · First Bolt

    Put a 100391 bolt through the face of a rail into the nut and tighten it clockwise with the 5 mm key.

  • 17

    Step 17: Side 1 · Other Three Bolts

    Tighten the other three bolts the same way.

  • 18

    Step 18: Side 1 · Boards

    Slide a board between the two rails of each side assembly.

  • 19

    Step 19: Frame 1 · Stand Panel 1

    Tip the four-board end panel up onto the ends of its posts, rails facing the bed.

  • 20

    Step 20: Frame 1 · Stand Panel 2

    Tip the guard-end panel up in the same way at the other end.

  • 21

    Step 21: Frame 2 · First Side Assembly

    Lower the long side assembly between the two panels, its board towards you.

  • 22

    Step 22: Frame 2 · Screws at Panel 1

    Drive two 128745 screws through panel 1's post into the end of the side rails.

  • 23

    Step 23: Frame 2 · Screws at Panel 2

    Drive two 128745 screws through panel 2's post into the other end.

  • 24

    Step 24: Frame 3 · Second Side Assembly

    Lower the short side assembly against the back of panel 1.

  • 25

    Step 25: Frame 3 · Two Screws

    Drive two 128745 screws through panel 1's post into its end.

  • 26

    Step 26: Ladder · Post

    Stand the ladder post at the free end of the short side assembly.

  • 27

    Step 27: Ladder · Countersunk Screw

    Drive the 100215 screw through the post into the upper side rail, clockwise. It sinks flush.

    Use the 100215 screw here, not a 128745.

  • 28

    Step 28: Ladder · Lower Screw

    Drive a 128745 screw through the post into the lower side rail.

  • 29

    Step 29: Ladder · Two Rungs

    Slide the two upper rungs in between the post and panel 2, the hole end towards panel 2.

  • 30

    Step 30: Ladder · Two Screws

    Drive a 128745 screw through panel 2's post into the end of each rung.

  • 31

    Step 31: Ladder · Last Rung

    Slide the third rung in below the others.

  • 32

    Step 32: Ladder · Last Screw

    Drive a 128745 screw into the end of the third rung.

  • 33

    Step 33: Rails · Ladder Side

    Lower the long rail onto the posts along the ladder side. In the finished bed it is the bottom rail.

  • 34

    Step 34: Rails · Three Screws

    Drive a 128745 screw down through the rail into each of the three posts.

  • 35

    Step 35: Rails · Far Side

    Lower the second long rail onto the posts along the other side.

  • 36

    Step 36: Rails · Two Screws

    Drive a 128745 screw down through the rail into each of the two posts.

  • 37

    Step 37: Channels · Both Sides

    Set a slat channel under each side rail, its round holes facing the inside of the frame.

    Both channels must sit the same distance from the side rails.

  • 38

    Step 38: Channels · First Screw

    Drive a 100343 screw through the channel into the rail, clockwise.

  • 39

    Step 39: Channels · Eight More

    Fit the other eight screws along the first channel.

  • 40

    Step 40: Channels · Second Channel

    Drive the first screw of the second channel.

  • 41

    Step 41: Channels · Eight More

    Fit the other eight screws along the second channel.

  • 42

    Step 42: Slats · Roll the Frame Over

    Roll the frame over onto its feet and push it back against the wall.

    Two people: hold the frame until it stands.

  • 43

    Step 43: Slats · Lay Them In

    Tilt the fourteen slats in through the open side and slide them along the channels until they are evenly spaced.

  • 44

    Step 44: Slats · First Snap Bolt

    From underneath, push a 105160 snap bolt up through the channel and a slat.

  • 45

    Step 45: Slats · Other 27

    Push in the other snap bolts, two in each slat.

  • 46

    Step 46: Slats · First Sleeve Nut

    Press a 104850 sleeve nut onto a snap bolt until it clicks, then tighten its slot with the flat screwdriver.

  • 47

    Step 47: Slats · Other 27

    Press a sleeve nut onto every other snap bolt and tighten it. The bed is ready for a mattress up to 12 cm thick.