# IKEA \- KURA Reversible Bed, White/Pine Assemble the IKEA KURA reversible bed \(90x200 cm\) in its loft position step by step, following manual AA\-1577020 By Numa Topic: Home & DIY [Open the interactive Jig](https://ask.jig.com/j/rK8svNCr7HYY) ## Guide ### 1. Parts and Tools The IKEA KURA reversible bed, 90 x 200 cm, built as the loft bed drawn on the manual's cover\. The two end panels lie either side of the bed's place, the two side assemblies on the rug, and the ladder post, rungs, rails, slat channels and slats beyond it\. You need a flat screwdriver; the hex keys come in the box\. Tap a part to see its name\. Two people are needed to stand the panels up and to roll the frame over\. ### 2. Panel 1 · Three Rails Lay bar 1 along the back of the four\-board end panel\. Push three of the five rails against its inner face, at the two ends and the middle\. ### 3. Panel 1 · First Screw Drive a 128745 screw through bar 1 into the end of a rail, clockwise, with the hex key\. ### 4. Panel 1 · Other Two Screws Drive the same screw into the other two rails\. ### 5. Panel 1 · Two More Rails Push the other two rails against bar 1, between the first three\. ### 6. Panel 1 · Four Boards Slide the four boards between the five rails, towards bar 1\. The boards are loose in their slots\. Do not glue them\. ### 7. Panel 1 · Bar 2 Set bar 2 against the other ends of the rails, parallel to bar 1\. ### 8. Panel 1 · Three Screws Drive a 128745 screw through bar 2 into each of the three rails that carry screws on bar 1\. ### 9. Panel 2 · Three Rails Lay bar 3 and push the three rails of the guard\-end panel against its inner face\. ### 10. Panel 2 · Three Screws Drive a 128745 screw through bar 3 into each rail\. ### 11. Panel 2 · Board Slide the single board between the middle and upper rails, towards bar 3\. ### 12. Panel 2 · Bar 4 Set bar 4 against the other ends of the rails\. ### 13. Panel 2 · Three Screws Drive a 128745 screw through bar 4 into each rail\. ### 14. Side 1 · First Nut The two rails of each side assembly lie either side of a short crossbar\. Push a cross\-dowel nut into the crossbar, slot facing up\. ### 15. Side 1 · Other Three Nuts Push in the other three nuts: two in each crossbar\. ### 16. Side 1 · First Bolt Put a 100391 bolt through the face of a rail into the nut and tighten it clockwise with the 5 mm key\. ### 17. Side 1 · Other Three Bolts Tighten the other three bolts the same way\. ### 18. Side 1 · Boards Slide a board between the two rails of each side assembly\. ### 19. Frame 1 · Stand Panel 1 Tip the four\-board end panel up onto the ends of its posts, rails facing the bed\. ### 20. Frame 1 · Stand Panel 2 Tip the guard\-end panel up in the same way at the other end\. ### 21. Frame 2 · First Side Assembly Lower the long side assembly between the two panels, its board towards you\. ### 22. Frame 2 · Screws at Panel 1 Drive two 128745 screws through panel 1's post into the end of the side rails\. ### 23. Frame 2 · Screws at Panel 2 Drive two 128745 screws through panel 2's post into the other end\. ### 24. Frame 3 · Second Side Assembly Lower the short side assembly against the back of panel 1\. ### 25. Frame 3 · Two Screws Drive two 128745 screws through panel 1's post into its end\. ### 26. Ladder · Post Stand the ladder post at the free end of the short side assembly\. ### 27. Ladder · Countersunk Screw Drive the 100215 screw through the post into the upper side rail, clockwise\. It sinks flush\. Use the 100215 screw here, not a 128745\. ### 28. Ladder · Lower Screw Drive a 128745 screw through the post into the lower side rail\. ### 29. Ladder · Two Rungs Slide the two upper rungs in between the post and panel 2, the hole end towards panel 2\. ### 30. Ladder · Two Screws Drive a 128745 screw through panel 2's post into the end of each rung\. ### 31. Ladder · Last Rung Slide the third rung in below the others\. ### 32. Ladder · Last Screw Drive a 128745 screw into the end of the third rung\. ### 33. Rails · Ladder Side Lower the long rail onto the posts along the ladder side\. In the finished bed it is the bottom rail\. ### 34. Rails · Three Screws Drive a 128745 screw down through the rail into each of the three posts\. ### 35. Rails · Far Side Lower the second long rail onto the posts along the other side\. ### 36. Rails · Two Screws Drive a 128745 screw down through the rail into each of the two posts\. ### 37. Channels · Both Sides Set a slat channel under each side rail, its round holes facing the inside of the frame\. Both channels must sit the same distance from the side rails\. ### 38. Channels · First Screw Drive a 100343 screw through the channel into the rail, clockwise\. ### 39. Channels · Eight More Fit the other eight screws along the first channel\. ### 40. Channels · Second Channel Drive the first screw of the second channel\. ### 41. Channels · Eight More Fit the other eight screws along the second channel\. ### 42. Slats · Roll the Frame Over Roll the frame over onto its feet and push it back against the wall\. Two people: hold the frame until it stands\. ### 43. Slats · Lay Them In Tilt the fourteen slats in through the open side and slide them along the channels until they are evenly spaced\. ### 44. Slats · First Snap Bolt From underneath, push a 105160 snap bolt up through the channel and a slat\. ### 45. Slats · Other 27 Push in the other snap bolts, two in each slat\. ### 46. Slats · First Sleeve Nut Press a 104850 sleeve nut onto a snap bolt until it clicks, then tighten its slot with the flat screwdriver\. ### 47. Slats · Other 27 Press a sleeve nut onto every other snap bolt and tighten it\. The bed is ready for a mattress up to 12 cm thick\.