ExploreMy JigsMission
MakeMake a Jig

© JigSpace Inc. 2026

jig.comContact@JigSpace on X

IKEA - BILLY Bookcase

publicRemix · Free
NBy Numa

Assemble an IKEA BILLY bookcase (80 x 28 x 202 cm) step by step, following manual AA-2587899

Transcript

31 steps · 4 min read
  1. 1

    Step 1: Parts and Tools

    Two side panels, a top, a bottom, a fixed shelf, a plinth rail, four shelves and a folded back panel, with the fittings laid out on a rug. You need a flat screwdriver, a cross-head screwdriver and a hammer. Tap a part to see its name.

    Assemble it with a second person, on a rug or the empty carton so the panels do not chip.

  2. 2

    Step 2: 1 · First Wood Dowel

    Push a wood dowel into one of the two holes in an end of the plinth rail, until half of it is in.

  3. 3

Step 3: 1 · Other Fifteen

Push in the other fifteen the same way: two in each end of the rail, the bottom, the fixed shelf and the top.

  • 4

    Step 4: 2 · First Cam Bolt

    Lay both side panels flat, inner face up. Screw a cam bolt into a hole in the inner face, clockwise with the cross-head screwdriver, until its collar meets the panel.

  • 5

    Step 5: 2 · Other Eleven

    Screw in the other eleven the same way: three pairs on each side panel, at the bottom, the middle and the top.

  • 6

    Step 6: 3 · Rail, Bottom and Fixed Shelf

    Stand the rail, the bottom and the fixed shelf on their ends on side panel #1 and push them down onto its dowels and cam bolts. The rail goes at the front of the bottom end.

  • 7

    Step 7: 4 · First Cam Lock

    Push a cam lock into a round hole in the bottom, next to the side panel. Turn it clockwise with the flat screwdriver until it grips the cam bolt.

  • 8

    Step 8: 4 · Other Three

    Fit and turn the other three the same way: one more in the bottom and two in the fixed shelf.

  • 9

    Step 9: 5 · The Top

    Push the top onto the far end of the side panel. Its round cam holes face out, away from the fixed shelf; the crossed-out copy shows it the wrong way round.

  • 10

    Step 10: 5 · Two Cam Locks

    Fit two cam locks in the top and turn them clockwise with the flat screwdriver.

  • 11

    Step 11: 6 · Side Panel #2

    Turn side panel #2 over, inner face down, and lower it onto the dowels and cam bolts of the rail and the three boards.

    Two people: one at each end of the panel.

  • 12

    Step 12: 7 · Six Cam Locks

    Fit six cam locks along side panel #2, two in each board, and turn each clockwise with the flat screwdriver until it locks.

  • 13

    Step 13: 8 · Onto Its Front

    Together, turn the bookcase forward onto its front so the open back faces up.

  • 14

    Step 14: 8 · Unfold the Back Panel

    Lift the folded back panel, turn it over and open it out along its fold, brown side up.

  • 15

    Step 15: 8 · Slide In the Back Panel

    Slide the back panel in from the bottom end along the grooves in both side panels, until it reaches the top.

  • 16

    Step 16: 9 · First Snap Sleeve

    Push a snap sleeve through a hole in the back panel into the board behind it, until its flange sits on the panel.

  • 17

    Step 17: 9 · First Snap Pin

    Push a snap pin into the sleeve until its head is flush. It spreads the sleeve and holds the back panel fast.

  • 18

    Step 18: 9 · Other Seventeen Sleeves

    Push a sleeve into each of the other seventeen holes: six across the bottom, six across the fixed shelf and six across the top.

  • 19

    Step 19: 9 · Other Seventeen Pins

    Push a pin into each of the other seventeen sleeves.

    No nails: the eighteen snaps hold the back panel.

  • 20

    Step 20: 10 · First Foot

    Set the two pins of a plastic foot into the holes in the bottom end of a side panel and tap it home with the hammer.

  • 21

    Step 21: 10 · Other Four

    Tap in the other four the same way: one more on each side panel and one in the middle of the rail.

  • 22

    Step 22: 11 · Stand It Up

    Together, tip the bookcase up onto its feet, turn it round and stand it with its back against the wall.

    A bookcase can tip over. Always fix it to the wall.

  • 23

    Step 23: 11 · Two Anchor Brackets

    Set the two angle brackets on the top, against the wall, with their short legs up.

  • 24

    Step 24: 11 · First Bracket Screw

    Put a washer on a short screw and drive it through the long slot of a bracket into the top, clockwise with the cross-head screwdriver.

  • 25

    Step 25: 11 · Second Bracket Screw

    Fix the other bracket to the top the same way.

  • 26

    Step 26: 11 · Into the Wall

    Fix each bracket to the wall with a screw and a washer through its short leg.

    Screws and plugs for the wall are not included. Use ones that suit your wall; ask a hardware shop if you are unsure.

  • 27

    Step 27: 12 · First Shelf Support

    Push a shelf support into a hole on the inside of a side panel, post up, at the height you want a shelf.

  • 28

    Step 28: 12 · Other Fifteen

    Push in the other fifteen: four at the same height for each shelf, two in each side panel.

  • 29

    Step 29: 13 · First Shelf

    Slide a shelf in from the front just above its four supports, then lower it so the holes underneath drop onto their posts.

  • 30

    Step 30: 13 · Other Three

    Fit the other three shelves the same way, two below the fixed shelf and two above it.

  • 31

    Step 31: Done

    The BILLY bookcase is assembled and fixed to the wall. Each shelf holds up to 30 kg; move the supports to change the shelf heights.

    Never let children climb or hang on the shelves.